WoodRiver - Mini Dust Collection Separator
Save 25% On WoodRiver Dust Connection Fittings, Hoses & Accessories Now Through August 31, 2020
Item 163730Model YW1062
Item 167542Model W1060
Item 164298Model YW1022
Item 142173Model YW1054
Item 163998Model Z-86
Item 151294Model 151294
• Cyclone style lid fits on a most 5-gallon buckets
• Inlet and outlet ports accept a 2-1/2" hose
• Features a foam gasket for a superior seal
• Elbow fitting on inlet side to induce cyclonic air flow
• Rugged ABS plastic for durability
After reading all the reviews I was a little hesitant. I picked it up because for about the same price of the collector I got free shipping. The connections are not standard size to have a shop vac hose hook up to it easily. I have run about 10 gallons of saw dust from a sander and a table saw and have not had to empty or clean the filter in my shop vac. I turned the elbow piece in the bucket towards the side so it immediately slows down all the particles as they come into the bucket.
It is always something
I have bought several of this type of Dust Collector over the years,they all work good, but you would think that they would make it the correct size for the normal shop vac hose or supply an adaptor to fit most hoses.
Great, once you get the hoses attached
My primary use for my shop vac is to clean up around my wood lathe. The separator worked exactly like it is supposed to. That is, after I got the hoses connected to it. I took the advise of another reviewer and got a couple of 2" no hub connectors from the plumbing department and they worked perfectly.
I would not buy this product again
Purchased the unit few months ago. I have had a very difficult time finding hoses that match the unit. I have a shop vac and the hose can not fit this product, even though the site notes it will fit 2.5" hoses. The Store is proposing I should jerry rig something to make it work or buy $8 fittings so the hoses would work!!
Total Waste of Time and Money
Normal shop vac hoses don't fit, had to buy two hubless adapters, $10.00 to make it fit the hoses. Then I started using it with my Ridgid 6 hp shop vac. It did not catch anything, all dust and debris continued on into the shop vac and started to clog the vac's filter. I bought to use with my chop saw and my table saw and general shop cleaning. It does not meet my expectations in any way. I built a rack to attach it to my shop vac for easier maneuverability, wast of time and materials. Bad Product.
serves my purpose
The product worked as I expected by removing large items from the vacuum stream. I had to find adapters to attach the hoses which added expense and time.
Needed to change the design a little
I purchased this product so i can put it inline between my wood working tools and my 12 gallon shop vac. After my first use, I open the 5 gallon bucket only to find it has been completely sucked cleaned by the shop vac. I tweaked it a little by dropping a 2.5" dust collection hose to the bottom of the bucket and filling water above the pipe line. It has essentially became a water trap and besides cleaning a messy 5 gallon bucket, the shop vac has very minimal dust.
It works fine - you just need to get the right size hoses to fit it. The standard hoses on my Shop Vac didn't fit it. But after I got the right hoses it worked fine.
works like expected
use for the miter saw and the table saw
I make rustic picture frames, this makes it so much easier, small and compact for I am limited on space
Works good, but ...
I have a Fein vacuum which I bought for its low noise. It is 2-1/4" diameter, so Duct Tape is a must for connections. The clear flexible hose I ordered is difficult to install, but eventually goes on and holds tight. The main problem is that the 9ft clear hose accordions to 3ft under suction from small nozzles and resists stretching. Use another type if that is a problem.
Didn't work for me
Maybe it's just not designed to work with a higher power vac, but 90% of chips and dust end up in my vac clogging up the filter every few minutes. If the thing was designed for low power systems, it should say so in the product description.
Works great for what it is
I read the reviews about the inlet and outlet ports being the same size as a standard shopvac hose. I have other tools that have the same problem. My solution is to go to the local home improvement store plumbing department to purchase 2" no hub couplers. The rubber fits tightly around both the inlet and the hose then the included clamps hold the two pieces together securely with no air leaks. I was a little concerned that the gasket material would leak air, but when I placed it on the bucket and turned on the vacuum the lid seated and I could not pull it off until the vacuum was turned off. For an inexpensive cyclone attachment to a standard shopvac this works great.
Standard shop vac hoses do not attach, as they are the same size as the inlets. No instructions to give any idea for a coupler, and standard couplers do not work. So where do I go from here, I don't want to resort to duct tape.
Allows only dust into the vacumn, no large chips.a
Not for me
Did not work for me. but it might just be me.
Great product for a woodshop
I use it to clean up my woodshop. Performs very well.
Portable dust collection made easy
Overall, very good product. It does reduce the vacuum's power, but with shorter hoses it is minor. Shorter hoses make it less of a hassle to set up, use, and move. I use it for portable dust collection on a table saw, reducing broom time. Full size version works great with dust collection system, but this is good with a shop vac.