Heavy Duty Leg Levelers, Small Foot, 4 pack
Perfect for cabinets, tables, or shelving units, these levelers feature a lipped mounting bracket that works to lift, support and create more stability. Small foot leveler, 1-5/16" diameter, comes...
- Set of four 1-5/16" diameter leg levelers, small foot
- Features a lipped mounting bracket
- Perfect for cabinets, tables, or shelving units
- Fixed base with plastic protective cap
- Made of heavy gauge, plated steel
second time i have bought these
i use these on all my table islands. i couldn't be happier with these. they are worth the money if you want micro adjusting shop table feet.
Great leg lever for shop projects.
Used on a router table base.
Good Leveling Accessory
Used the levelers on a large Christmas Tree display which includes a G scale Christmas train display. Perfect for the large base.
Level is good
Great. For old floors
Strong but Wrong
The image might lead you to believe that the foot remains planted as the threaded rod is turned. Not so(WoodCraft probably changed vendors). The foot turns with the rod so that your cabinet walks away from the desired location as you adjust it up or down. I had to make some separate cups for them to ride in. Then I braded the cups to the floor. For some odd reason the wrench pockets are just a wee bit tight so that your wrench gets stuck. I tried several wrenches.
good for workbench leveling
I attached these leveling feet to a sharpening bench I just built. They work great and are easy to adjust, and the screws for mounting them are included. The plastic bottoms can be a little slippery, but if they are supporting a heavy load there is enough friction to prevent most movement.
Yhese levelers are easy to install and use. Only takes a few minutes.
saved bed from sloping hardwood floor
this was exactly the product i was searching for!
Real time saver
Real time saver installing cabinets over uneven concrete or tiled floors. Keeps cabinets off floors should water spill or a pipe leakes. You never know. You'll need a longer allen wrench then supplied. If you have cabinets without a removable toe kick you'll also need plastic plugs for holes drilled for access.
These leg levelers work great
I built and out-feed table/storage unit for my table saw and needed something to make it the same height as my saw. I didn't want to spend a lot of money but wanted something that would support the weight of some tools. These fit my needs to a tee.
Definitely recommend to others
I bought these for an out-feed table that I built for my table saw. It has a torsion box top so it is very heavy. These levelers were able to match the height of the out-feed table to my saw without any problem at all. The other plus is that they were very reasonably priced.
Heavy Duty Leg Levelers, Small Foot
This product is easy to install. You can't do it wrong. It is a little difficult to align the hex wrench to the leveler adjustment shaft when leveling, but no big deal. I have used these levelers before in my shop and they work very well for leveling my cabinets on an uneven cement floor.
my garage floor is so uneven that I was forced to use shim under my dead flat assembly table in order to keep it level. I wanted to use leveling feet but couldn't find any that would fit until I saw these. The only reason I had a hard time installing was because of how heavy my table is!! Once they are under and screwed in, the hex key makes it easy left or drop each corner. See the photo; scribing was not an option!
Catalog description lacks height measurement - if you're installing these on bookcases, your kickplate must be at least 2.5" tall. These are sufficiently "heavy duty" in design to hold a lot of weight, allow you to correct for an uneven floor, and move the case without floor damage. I'll be using these again on my next project.
The #5 hex wrench used for adjustment has to be cut down. The tail of the hex wrench is too long and hits the vertical support. Other than the fact this should have been tested the product itself is easy to install and is well made. Just be prepared to cut the hex wrench tail in half.
The only improvement I might add would be to beef up the nut threads. But will work great for a mobile table saw base.
Well Made and inexpensive
Heavy duty but needs jam nut
This foot has heavy duty metal on the support area. The foot is hard plastic so it may crack but not sure yet. The foot shaft needs a jam nut to keep it set at the level you set. The nuts were readily available at my local hardware store.