View a Larger Image of Clean Sweep Bandsaw Brush
Item 146153
Model AC-CSB2000

Carter Products - Clean Sweep Bandsaw Brush

$9.99

(9) Reviews
Write a Review
In Stock check in-store availability

The Clean sweep helps keep your Bandsaw's tires free from debris which shorten their life and effect blade tracking. As debris; saw dust, metal on metalworking saws, or any other debris accumulates...

More Details
Articles & Blogs

Compare With

Details

The Clean sweep helps keep your Bandsaw's tires free from debris which shorten their life and effect blade tracking. As debris; saw dust, metal on metalworking saws, or any other debris accumulates on the tire, continued use without cleaning compresses the tire more in other places then if it were in contact with the rubber or urethane alone. Over time the tire will loose its rebound in those places if not cleaned properly and thus decrease tire life. (Currently only offered for 14" saws)



  • Extend bandsaw tire life
  • Easy to install
  • Simple but effective upgrade to any bandsaw
  • Mounts against lower wheel

Articles & Blogs

Upgrades1

12 ways to supercharge (or spruce up) your favorite sawyer.

Read More >
Bandsaw tune up yt thumb

A well-tuned bandsaw can provide you with the means to cut large sweeping curves, cut custom veneer and even produce your own rough-sawn lumber from a log.

Read More >

Reviews

9 Reviews
Write a Review
  1. by on

    Glad I bought for My Jet 14" Band Saw

    I bought my Jet 14 inch band saw new at Woodcraft about 8 - 10 years ago. I cut out the lower area and have a 4" fitting for my Dust collector which has helped with the dust, but the tires still get full of dust and grit. I bought new Jet replacement tires for my saw and decided now would the time to try and fit some brushes to keep the tires cleaner. My jet is older and does not have any provisions for brushes like the new ones do. I bought two "Cleansweep" brushes and managed to find a way to mount them. I wish I could post my photos here to show their placement. The upper one I used a small piece of red oak with one end screw screwed into the saw and then screwed the brush to the other end . The lower was much easier just screwing it to the saw. as shown in product info photo. (Both my brushes are screwed into the blade guard piece that you remove when changing blades) It is working great and keeping the tires much cleaner than before. My only complaints are I wish they would tell you what size drill bit to use, very difficult choosing the right size especially when screwing into metal. Also wish they would make the brush stiffer.

  2. by on

    Works well

    I've never used one before. It does a good job keeping the tire cleaner. Too bad my saw does not have a way to mount a second one for the other wheel.

  3. by on

    good accessory

    Easily installed, does what it's supposed to, a good [$] improvement.

  4. by on

    Small but works

    Works well and extends tire life.

  5. by on

    A no-brainer

    If your saw doesn't have a tire brush, install one. It will keep the sawdust and crud from building up on your tire, which legnthens the life. A no-brainer...

  6. by on

    I would buy this product again and again

    Easy tune up part to improve the over all performance of most bandsaws.

  7. by on

    It's Worth the trouble

    Had to relocate the upper brush to make it work properly.

  8. by on

    Simple, but effective

    I have a Jet 14" bandsaw. Bandsaws of this type are notorious for their lousy dust collection. After use, I usually cleaned the inside of the lower door area and while doing so, scraped the caked on sawdust from the band saw tire. On a whim. probably to get my order over a certain amount for free shipping, I added this little brush. I am amazed at how good a job this silly little thing does. In a nutshell, easy to install and quite effective.

  9. by on

    Nice additional to my bandsaw

    The Carter brush is a nice addition to my HF 14 inch bandsaw. Easy to install and keeps the tire nice and clean.