View a Larger Image of 4" Hose Splice Fitting for Dust Collection System
View a Larger Image of 4" Hose Splice Fitting for Dust Collection System
  • View a Different Image of 4" Hose Splice Fitting for Dust Collection System
  • View a Different Image of 4" Hose Splice Fitting for Dust Collection System

WoodRiver Dust Connection

4" Hose Splice Fitting for Dust Collection System

$5.99

$7.99

Save 25% - Give Your Shop A Clean Sweep!

WoodRiver® Dust Connection™ Hose Splice Dust Collection Fitting allows you to connect two sections of common 4" dust collection hose together to form a longer run. Fitting is nominal 4" OD with overall length of 6" to provide room to slide on hose and apply hose clamps on both sides of...

Details

WoodRiver® Dust Connection™ Hose Splice Dust Collection Fitting allows you to connect two sections of common 4" dust collection hose together to form a longer run. Fitting is nominal 4" OD with overall length of 6" to provide room to slide on hose and apply hose clamps on both sides of the connection. Molded using plastic resin material to maintain shape and withstand woodshop environment.

Features:

  • Splice fitting to connect two lengths of 4" dust collection hose
  • Tapered port each end fits inside most 4” dust collection hose
  • Large diameter middle section for ease of assembly
  • Constructed of tough abrasion resistant plastic resins
Specifications:
  • Overall Length: approximately 6"
  • Size: nominal 4" OD
  • Use: connect two sections of common 4" dust collection hose together to form a longer run
What's Included:
  • (1) WoodRiver Dust Connection - 4" Hose Splice Dust Collection Fitting
Notes:
  • Recommend 4" wire hose clamps #85U66 (sold separately).

Reviews

3.83 out of 5 stars
6 Reviews
  1. 4.0 out of 5 stars
    by on

    This turned out to be useful for me!

    This hose splice turned out to be good for plugging into a few other items. It fits loosely into PVC pipe (the non-pressure bearing pipe, DWV), sometime a bit better than loose. It also fit quite nicely into a 4" DWV elbow, on the small end, which usually goes inside the PVC pipe. This makes a pretty nice quick connect. I also found I could use one of those rubber and hose clamp join pieces on my bandsaw outlet, leaving half hanging off the port. Then I could tighten the hose clamp on that half so that this splice would fit inside very nicely. So far, I have not used it to splice together the 4" clear hose. It is a bit tedious putting the hose onto it, but it works ok. I give it 4 stars because it turned out to be useful, unlike nearly every other fitting I bought. I took off a star because of the general frustration of using these sorts of fittings.

  2. 4.0 out of 5 stars
    by on

    would buy again

    easy to attach

  3. 4.0 out of 5 stars
    by on

    It wasn't what I thought it was

    This is for connecting two hoses together and it was so difficult to do that I will not buy anymore of these. Once on it works pretty well and so far hasn't come apart.

  4. 4.0 out of 5 stars
    by on

    Quick Change

    I love the quick connection for the dust collector. When you have a small shop and one dust collector, it is nice to be able to change the hoses quickly. This works when I need to use more than one hose.

  5. 4.0 out of 5 stars
    by on

    Does what it is intended to do

    This 4" male to male connector has no flaws. It does what it is supposed to do. My only gripe is cost. [$] for a few ounces of plastic molded into a single piece seems a bit much to me. I could sand-cast these out of scrap aluminun for less than [$].

  6. 3.0 out of 5 stars
    by on

    It works for what it's intended for

    I use these to connect the larger machine's in my shop to the dust collection system.

Compare With

Top of Page