WoodRiver - Workbench Caster Set 4-piece
Wouldn’t it be nice to have your workbench where you needed it? Now you can. Rugged steel construction gives these WoodRiver® casters 110-lb. capacity (440 lbs. per set). The casters swivel 360°,...
Item 159652Model 159652W
Item 140642Model 140642
Item 141053Model 141053W
Item 141052Model 141052W
Item 152836Model 152836W
Item 152837Model 152837W
Item 152839Model 152839W
• 110-lb. capacity per caster
• Foot activated lift
• 360° maneuverability
• Rugged steel construction; Satin black finish
• Includes all mounting screws and instructions
Articles & Blogs
Good, functional workbenches
are good and functional because they have mass, they are heavy, and they do not
“move” when you’re working on them. The
mass and weight that provide the solid, stable platform for woodworking also
make these benches difficult to move, or relocate in the shop. If your shop is
a shared location like a garage, or even if you have a dedicated permanent
shop, the ability to easily relocate your bench becomes a necessity, not a
Went on easy on quick. Sure makes moving my heavy bench easy.
Caster mounting plate bent on several, very difficult to use now
I installed these on a bench which holds my hobby CNC setup, machine is approx. 200 lbs and bench is approx. 120 lbs. So well within the weight limits given. After installing and raising/lowering the bench several times I noticed it was not rolling nearly as smoothly as before. After inspecting, 3 of the 4 casters had bent plates. When you step down on the lever, there is the rounded part of the lever that drives the plate with the caster down. Then as you continue to step down, the rounded edge rotates past and the longer straight part of the lever is all the way down on the caster, essentially locking the caster in the down position. On three of mine, the plate the caster mounts to bent right where the rounded part of the lever hits it. This causes two issues. First the caster doesn't go down as far (which I could live with). But more importantly, when the plate is bent, the caster axis no longer sits perpendicular to the floor. This means that every time you try to change direction when the caster swivels, the bench actually has to move up or down some which makes it difficult to move the casters and they tend to self rotate so the wheel is all the way out, causing the bench to move unexpectedly. Probably ok for lighter weight benches, but I would be skeptical buying this is you know for certain the weight of your setup is 300lbs or more.
Installed these today and did a YouTube video of the install. Extremely easy to install and works great. Moved my bench around with one hand easily.
Work like advertised
Just finished installing a set of these casters on my workbench 18X96, two deck 2X4 with 3/4 ply. It's a heavy bench even when not loaded. Everything I need in the box including clear instructions. Total time installing was abut an hour. Worked like a charm and rolls very freely on my basement floor completely loaded.
Everything they're supposed to be!!
I was very skeptical about these, as they are pricey! However, I just installed them on my custom midi lathe rig that I'd been muscling around the garage and-WOW! I'm a believer. The instructions are a bit vague,which adds to the difficulty when coupled with a heavy bench, and if your floor is slightly out of level, you'll need to compensate for it. But SO FAR, these are the ticket!
Some folks have said there were no instructions; mine came with a simple diagram noting the mounting hole centerline heights from the floor; that's all that's necessary. Except that the mounting screws included appear to be about #10 self tapping and that doesn't cut it when using these near the rated capacity. So I bored out the holes and used 5/16" lag screws, except that the top hole was almost dead center on the assembly bolt hole for my bench. So I drilled to 3/16" holes left and right at the top and used the included screws there. I have to say I wish these were about 20% more robust. My bench had a shipping weight of 350 lbs. and after loading it with tools I think it approaches 90% of rated capacity. A stronger design would make me feel better and I would pay some premium for that. Lastly, they are hard to operate on my heavy bench, especially at the end with the tail vise where the overhang is more extreme. Not sorry I bought them, just thoughts on my setup. Cheers, Al
Wow - they work great!
I am a picture framer, and have some very heavy workbenches. I installed these on the bench which holds my dry mount press (which alone is very heavy). The casters were easy to install, and work great. I am going to buy a set for each of my benches.
Worth every penny
I have a very heavy bench : 85" long by 29" wide with heavy maple top complimented by large English front vise, a full width twin screw vise and a patternmakers vise. The base is made from old growth Doug fir 4x4s with 2x6 stretchers of the same. There are two full length shelves houses some of my collection of iron and wood planes plus a cast iron miter box and saw and a bunch of other stuff. So I am putting these casters to the test and they have passed, no problem. I mounted them on the inside of the pieces that connect the legs and serve as the feet at both ends so I would not be kicking them. It makes them a little harder to operate, meaning that they are partly under the stretchers thereby restricting foot access to the lever. I get a grip on the corner and lift a little as I press the lever to help a little and as my bench's weight is probably close to their limit. The floor does need to be clean as they only lift 3/8" and I don't want to stress them by trying to roll over a large chip. I do some pretty rough work with large chisel and hatchet, woodbutchery you could call it, so the chips are sometimes way more than shavings. Any way the bottom line is these are the casters I have always wanted for my bench and have made it, the largest thing in my shop, as mobil as my machinery has been for years. I looked at other outfits similar items and while the made similar or greater claims for load carrying the Woodcraft casters looked much beefier. Thanks for a great product Woodcraft!