View a Larger Image of Seam Ripper Kit Gold
View a Larger Image of Seam Ripper Kit Gold
  • View a Different Image of Seam Ripper Kit Gold
  • View a Different Image of Seam Ripper Kit Gold
WoodRiver 1110SR-HP-1
Item 154328

Seam Ripper Kit Gold

$6.99

Qty 1-9 10-19 20+
Each $6.99 $6.29 $5.94

Turn your own custom seam ripper. This kit includes a sharp reversible blade that can be stored in the handle when not in use. A clip is also included to secure the seam ripper to any pocket....

You May Also Like

Details

Turn your own custom seam ripper. This kit includes a sharp reversible blade that can be stored in the handle when not in use. A clip is also included to secure the seam ripper to any pocket. Durable Woodcraft gold plating.



  • Easy & fun kit to create


  • Reversible blade can be stored inside of the handle


  • Excellent sewing accessory


  • Durable Woodcraft gold plating


Instructions / MSDS

Articles & Blogs

This chart outlines the proper blanks, drills and accessories to make various pens and small turning kits.

Read More >
Thinkpink1

October is the month for pumpkins, colorful leaves and Halloween costumes.  For many woodworkers, it’s the time of year when the weather cools down and they get back into their workshops.  It’s also the perfect opportunity to create some fabulous “pink” pens in recognition of Breast Cancer Awareness month.

Read More >

Reviews

3.83 out of 5 stars
6 Reviews
  1. 5.0 out of 5 stars
    by on

    Easy to turn works well

    Makes a great gift for sewers. I have turned 10+ and the only problem I have had is getting the brass tube glued into the wood blank. After reading other reviews I always use a counter sink to taper the inside edge of the tube after gluing. Do not use a drill. Hand turn the reamer and slightly taper the insertion point. Do not leave sharp corners to tear the O rings. My only problem is I would like to find a source for a few extra O rings.

  2. 5.0 out of 5 stars
    by on

    Good product

    clean tube and remove burrs with fine chain saw file works wonders. and put a little vaseline on O ring after installation on piece.

  3. 2.0 out of 5 stars
    by on

    No Replacement Blades available

    I like the weight and feel of this item. I called customer service to see if I could order a replacememt blade. Its labeled as Part A in the instructions. This is even threaded and would make replacing a blade easy. But no replacement blades are availible.

  4. 4.0 out of 5 stars
    by on

    Nice product

    I like these kits. I had a problem too with the o-ring on the first one I made because I had glue leak into the tube. I now pack the tube with modeling clay to keep it clean. I wouldn't recommend sanding the inside of the tube. The rougher surface stops the o-rings from working smooth. Debur, chamfer and polishing the inside is ok to do. I find if you just wet the o-ring slightly they slide in nice. It would be nice if they put a couple of extra o-rings in the package. My wife is a quilter and uses it a lot.

  5. 3.0 out of 5 stars
    by on

    Seam Ripper assembly fixes

    The O-rings when installed on the blade holder make it to large to fit inside the brass tube. I have found that by turning the blade holder on my lathe in a chuck fitted with pin jaws I can sand the grove and reduce the diameter enough that the O-rings will fit inside the brass tubes. It take a few attempts to get the fit right. I also chamfer the brass tube slightly. I've also noticed while test fitting the blade holder (with the O-rings installed) that twisting the blade holder while pushing it in the tube works the best. Often no further modification is required.

  6. 4.0 out of 5 stars
    by on

    Slight problem

    Received my order for 5 kits on 1/26/12 and upon inspection was impressed. I ordered these after reading too many negative reviews at other merchants sites and felt that the quality here would satisfy my needs. The kit is very well made, BUT the interior diameter of the brass tube is too small when the "O" rings are installed, and too large without them. Solution: De-burr the tube as instructed and with a split mandrel that fits sloppily inside the tube, cut a piece of 220 grit sand paper to size, and enlarge the interior, then with length of 1/4" dowel chucked in your lathe charge it with emory compound and polish the interior until you achieve a good fit. It may take several attempts - and it really slows down production. Without opening the inside diameter the fit is so tight as to either ruin the "O" rings, or be way too hard for the recipient to use. Short of a custom reamer, I have not found a better way to enlarge the tube. Hopefully one of you will and so advise. I gave it a 4 star rating because it does have potential and would recommend it with the above understanding. Wes

Top of Page