WoodRiver - 5" Caster Double Locking Swiveling with 4 Hole Mounting Plate
Put your entire shop on wheels! Load rating for each caster is 264 lbs. Easy rolling, non-marring, polyurethane tires will not "flat spot" during long periods of remaining stationary. Swivel and...
Item 141050Model 141050W
Item 152838Model 152838W
Item 141051Model 141051W
Item 141053Model 141053W
Item 141054Model 141054W
Item 152836Model 152836W
Item 140639Model 140639
Item 162389Model CAX3SC
Item 148594Model 148594
Item 159652Model 159652W
- Double Locking
- Load rating for each caster is 264 lbs
- Plate size is 2-3/4" W x 3-3/4" L
- Distance between holes is 1-3/4" x 3" center to center
Articles & Blogs
Continuing our woodworking adventures into Alabama, we arrive at the home of Woodcraft Magazine senior editor, Joe Hurst-Wajszczuk to cover his 20′ x 22′ interior garage space morphing into an extreme workshop makeover. The 2011 October/ November Issue #43 of Woodcraft Magazine features a special topic on this floor to ceiling, wall to wall transformation with detailed projects, providing instruction on turning any garage, basement or outside structure into a viable workshop. Joe is tasked with converting his 20′ x 20′ two-car attached garage into an organized, fully functioning, safe workshop. The “BEFORE” photo below will give you an idea of what Joe started with. If the clutter and disorganization looks similar to your work area, then perhaps this information may help you build a workshop makeover too.
asked woodworker Dave Clarke, who was diagnosed with ALS in 2018, to take a look at an article Woodcraft
Magazine published in Issue 44 by Pete Stephano – “The Wheelchair
Woodworker Shop” – to see if he felt that the recommendations were still
relevant and if he had any other advice for folks wanting to set up a workshop
with modifications. Read more here...
Red "tire" failed coming off in pieces - only one of four failed, so don't think that it was overloaded
used on heavy mobile blacksmith forge
I built a 2" X 6" wood frame for a large old cast iron blacksmith forge, and its cast iron blower, and needed to replace 3" casters which were too low. The 5" ones work nicely as I winch the forge up a ramp onto my trailer to go demonstrate blacksmithing at other sites, often rough ground. No effects from exposure to rain and sun, heat or cold. Brakes hold well while trailering. 2 casters used with 2 of the 5" non-caster wheels, so the rig doesn't go sidewise on side slopes. Very satisfied.
Bought to replace old wheels.
Used on tool chest.
best casters I've used
All of my work stations are on these casters.They are smooth and make moving my stations around easy.
Durable and good looking
I've been using this type of castor in the workshop for awhile and haven't been disappointed. Recently, I built a large heavy duty potting bench that could be moved around. These castors were just the right match with a 5" clearance and a load rating of 300 lbs per wheel. I also like the red rubber wheels as they are easy to see.
Short life span!
These casters were great the first 2 years, but then the red layer began to crack and then fell apart. Now you can no longer lock the wheels because the black inner tire is too small for the brake to touch. For the price, I expected longer service. I won't be buying any more.
Hard to unlock
The locking mechanism is the same size on the 3", 4", and 5" wheels. The smaller sizes are very easy to unlock. The largest diameter wheel crowds the locking/unlocking tabs which makes them harder to unlock. The taller wheels though will climb over rough or bumpy surfaces more easily. In any size though these are better wheels than other brands I have in my shop.
I like the double lock on the wheels
I put the wheels under my roll around cabnet that is in my small shop.
quality at reasonable price
smooth rolling, quality caster
I use these wheels under all the tools in my shop. Replaced the small wheels on my Delta Unisaw with these wheels