Working with Lacquer

Lacquer may just be the best all-round film building finish on the planet. No matter how hard you look, you won’t find another finish that dries as fast, rubs out as easily, and imparts the same clarity and color. But despite these advantages, lacquer’s bad reputation for fumes, flammability, and finishing problems keeps it out of many shops. Now’s the time to put those fears aside and give lacquer a closer look.    

  For starters, look at the Finish Drying Time chart. Professional woodworkers needing to ship one project before starting the next know these numbers by heart. Even if your paycheck isn’t riding on the next project, lacquer’s super-fast drying time means less opportunity for dust damage, and faster finishing room turnarounds. Lacquered projects can be gift-ready when other finishes are still stuck in mid-cure. 

 Following is some basic advice for applying lacquer with a spray can, brush, and rag. With luck, applying the finish on your next project may take less time than reading about how it’s done. Note: See the Convenience-Plus Buying Guide for the products in this story.

Why the Mask Matters

Lacquer is at the upper end of the workshop-toxicity scale, but nearly every label—including the enviro-friendlies—lists some sobering safety notes. These warnings are based upon occupational (eight-hour day) exposure, but when facing potential liver, nervous system, and/or brain damage, there’s no point in quibbling over the fine print.

When you spray, wear a mask. Be sure that it’s NIOSH-approved for organic vapors and gases.

As a rule, replace the filter when you detect the first faint whiff of finish, but for backup, stick a piece of tape on the mask and make a tick mark every time you don your mask. By tracking the number of times a mask’s been used, you can be sure to have fresh filters ready before a big job, or make a preemptive filter switch before smelling anything on your side of the mask.

Note that charcoal, the active ingredient within the cartridge, absorbs chemicals whether or not it’s strapped to your face. To extend its service life, store your mask in a re-sealable plastic bag.

 

Stick with spraying for the small stuff

Spraying takes full advantage of lacquer’s fast-drying ability. Safe from dust in 15 minutes, lacquer competes with oils and wiping varnishes as a dust-dodger, but offers a great looking film. And since the solvents evaporate in less than week, lacquer is perfect for last-minute gifts.

 Unfortunately, the fast-acting solvents also give lacquer its bad reputation. Spraying atomizes solvent and lacquer to create a serious health and fire risk. Good ventilation and a mask will protect you, but don’t think of using a HVLP system unless your shop’s equipped with a designated spray booth and explosion-proof fan. To be safe, reserve spraying for smaller projects, and stick with the can. Do your spray finishing outdoors or in the garage with the door wide open

 Better-quality spray cans armed with fan-shaped tips deliver finish as smoothly as you’d expect from a high-priced HVLP sprayer. But you will need to spray more coats for the same build. You’ll also pay more for the convenience of the spray can.

Spray-can finishing isn’t tough, but a few tips can help you achieve better looking results: 

Provide good light. Position your work so that you can see the reflection of a wet coat. This makes it easier to see what you’ve done and to make sure each coat overlaps the next. 

Plan your moves. Develop a spraying strategy that starts with the least visible and ends with the most visible sections of your project. Make a practice run on a piece of cardboard to avoid first timer puddles or runs on your project.                                                                                                                                                                                                                                              

Keep the gun moving. To avoid spits and stops, depress the valve a few inches early, pass the can over the wood (6" to 8" away), then release it when the can’s a few inches past your piece. Repeat the process, overlapping each pass by about 50%.

 Cover up when you’re done. Use a scrap of plywood, or cardboard box as a dust-umbrella to protect your freshly finished work for the first 15 minutes. Nothing’s worse than finding a speck of dust that decided to take a swan dive into a perfectly smooth surface.

    Brushing best for big projects Due to the past prejudices (lacquer is too tough to brush; fears of fumes and flammability) lacquer lags way behind polyurethane. This finish doesn’t deserve such a bad rap. Brushing lacquer isn’t any more difficult than brushing the fast-drying waterbornes and reformulated low-VOC finishes you’re already using. Open a window or two, and you’ll discover that lacquer’s attributes outweigh the solvent smell. A project can be recoated, rubbed out, and removed from your shop in about the same time it takes to lay on three coats of poly.

A few tips can help get you started down the road of faster finishing. For starters, use a better brush. Cheap won’t cut it; lacquer solvents dissolve foam brushes and can bleed color onto your work from dyed bargain basement bristles. At the other extreme, top-shelf brushes are a joy to work with, but since lacquer is self-leveling, you don’t need to do so much brushwork. Any good-quality natural bristle brush with flagged tips (flagged, or split, tips carry more finish and deliver it more evenly onto the workpiece) should do the trick.

 Brushing is a simple three-step process: brush it on, tip it off, then leave it alone. The biggest trick is learning to work quickly, and buying into that last step.

 

Working with the grain, brush on a nice even coat. When the brush starts to drag, flip it over to transfer the lacquer clinging to the other side. Next, hold your brush at 90° to the surface and lightly graze (or tip) the surface with the ends of the bristles. Tipping knocks down brush marks and blends each pass with the last. Repeat the first two steps, barely overlapping each pass, until you’ve finished the surface. 

 Now walk away. You’ll soon discover most brush marks will self-level, or disappear when you brush on the next coat. Drips are the only exception to the rule. It’s OK to brush out a drip, as long as it’s caught immediately. If you find a drip that’s a few strokes old, leave it; you’ll only ruin the surrounding area with ugly brush marks. Refer to the sidebar below for a simple spot treatment.                                          

Between coats, search and slice off bumps, then lightly sand the entire piece with 320-grit before applying the next coat. As you build the finish, and your technique improves, the surface should get progressively smoother. Each coat should require less touch-up. By the third or fourth coat, give the finish a day or two to harden then you’re ready to proceed to rub out.

Rub out for a soft shine Lacquer is the easiest finish to polish to a high gloss, but because it’s easier to scratch, it’s tough to keep it that way. A high-satin look–similar to what you’d find in the furniture stores–is a nice compromise because it’s easy to obtain and maintain. The best thing is that you can use your sander to do most of the heavy lifting. Here’s how.

  Give the finish a day or two to cure then lightly rub out with 0000 steel wool. Next, apply a dollop of Deluxing Compound, to a Surbuf pad, and put your random-orbit sander to work. To eliminate any risk of sanding tail marks, creep your sander across your work. When done, wipe off the remaining haze with a soft rag.

The abrasive wax makes minor repairs a no-brainer. When a surface loses its luster, treat it to a quick buffing.

 

Lacquer at the Lathe Lacquer really shines at the lathe because the finishing process takes full advantage of lacquer’s lightning-fast drying time. Because you’re working on the piece as it spins, sags, brushmarks and drips are non-existent. Using a rag and applying the lacquer a few drops at a time keeps solvent exposure to a minimum. 

 To prepare your turning for lacquer, sand up to 400 grit to remove tool marks and to begin sealing exposed end grain. (If you want to add color at this point, try using alcohol-based dye while the wood is moving. The alcohol improves absorption and dries immediately.)

 

First, turn the lathe off and wipe on a generous coat of sanding sealer. (Trying to seal an object while it’s spinning would splash finish all over your shop.) The goal is to saturate the surface, completely sealing the pores and making an even base so that the topcoats can build up. When the piece dries to the touch—it should only take a few minutes—sand out rough patches with 600 grit. 

Next, turn the lathe on and apply lacquer with a small lint-free rag. After wiping on a thin coat, slide the rag to the start of that section and firmly press it against the wood. The friction helps the finish dry faster and removes imperfections for a smoother, shiny film.

 

Back to blog Back to issue