Woodsense: Spotlight on SapeleComments (0)
This article is from Issue 77 of Woodcraft Magazine.
A shimmery mahogany substitute
Since the days of Thomas Chippendale, woodworkers have
enjoyed a love affair with mahogany. Sadly, over the course of two centuries,
genuine mahogany (Swietnia macrophylla) has been listed as an endangered
species. As a result, this Cadillac of cabinet woods has become extremely
difficult to find and prohibitively expensive. In response, lumber dealers have
relabeled several sustainable substitute species as “mahogany.” Of the bunch,
sapele—pronounced sah-PELL-ay—(Entandrophragma cylindricium) stands out from
a member of a different species, sapele (a.k.a. sapelli or sapeli) has a
similar reddish-orange color as mahogany. When quartersawn, sapele boards
exhibit a uniform ribbon pattern that shimmers in the light. In flatsawn
boards, this squirrelly grain makes for wild swirls and surfaces that shift
color depending on how the light strikes. This beautiful pattern occurs
because sapele’s grain is “rowed” or interlocked, which can make planing and
shaping tricky. Despite some challenges, sapele’s color and lively grain make
this wood worth the effort it takes to tame. Read on to learn how to select the
best boards and make the most of them.
Where the wood comes from
Sapele comes from a large tree in tropical
Africa that is commonly referred to as aboudikro. Its range includes Sierra
Leone, Angola, Congo, and Uganda. Aboudikro is a deciduous tree that commonly
reaches a height of 130 feet. At this time, sapele is not on the endangered
species list, though many of the countries where it grows have established
protected populations and restrictions on lumbering. The IUCN (International
Union for Conservation of Nature) lists the species as “vulnerable” due to a
decline in its natural range and exploitation.
History in woodworking
Until recently, sapele was used mainly for veneer in decorative plywoods—its uniform ribbon stripes create a beautiful and predictable pattern that’s prized by designers. General Motors uses sapele for the interior trim in Cadillacs. Luthiers use it to make guitars and ukeleles. High-end carpenters rely on sapele as a mahogany substitute for floors, staircases, and trim work. Highly figured boards are often reserved by furnituremakers for door panels and tabletops.
How to select the best stock
Good sapele is easy to find. It is commonly available in 4/4 stock, and because the lumber is harvested from large trees, you can often find wide planks (48" and wider) and in thicknesses up to 16/4. Prices for typical stock (4/4 or 5/4, up to about 8" wide) range from $6-$8 per board foot; about 50% less than African mahogany. Of course, you’ll pay at least twice that for highly figured stock and/or wider pieces. Most trees are quartersawn to showcase sapele’s distinctive ribbon figure, where each stripe seems to change from dark to light as you walk around a finished project.
Sapele is a beautiful hardwood in its own right,
but is generally lighter than true mahogany, (see “Mahogany’s Mimic,”)
and has more color variation. While you’re likely to find many rich, reddish-orange
brown boards, there can be quite a bit of difference from one to the next. Boards
ranging from tan to a deep burgundy are common. Bring your block plane when
buying roughsawn stock, and ask if you can plane a small area to see what the
color actually looks like.
Working sapele in the
Although sapele resembles mahogany, you’ll find that jointing, planing, and routing can be more difficult because of its rowed grain. With most woods, if a board suffers tearout when you run it one way, running it the opposite direction usually solves the problem. Not so with sapele. Freshly sharpened jointer and planer knives and light passes can help. However, because of the interlocked grain, accept that you’ll have some tearout no matter which way you cut. Just settle on the direction that minimizes the damage. When edge jointing boards, you may find that you get better results from the table saw than from your jointer.
As for hand tools, you’re likely to find that scrapers work better than hand planes. When carving, say, a ball-and-claw foot for a Chippendale chair, invest time keeping your chisels extra sharp. And pay close attention to what the grain is doing.Sapele scrapes and sands easily, but note that sanding and machining produce a fine dust that will stick to everything. While severe allergic reactions are rare, sapele is still considered a skin and respiratory irritant. To minimize the chance of an adverse reaction, try to collect dust at its source, wear a dust mask, and plan on spending extra time vacuuming the shop at the end of the build.
AromatherapyIt has been over three weeks since I finished the chair featured on page 50, but every time I enter my shop, I can still smell sapele’s distinctive aroma. The wood’s fragrance is sometimes likened to Spanish cedar, but I find it darker and more exotic. Whatever you think, it is certainly long lasting. Although the dust seems to stick to everything, I’m tempted to wait a few more weeks before cleaning up my shop.
Sapele, Ribbon - 1/4" x 3" x 24"Item 861513
Sapele, Ribbon - 3/8" x 3" x 24"Item 861514
Sapele, Ribbon - 1/2" x 3" x 24"Item 861515
Sapele, Ribbon - 3/4" x 3" x 24"Item 861516
You must be logged in to write a comment. Log In