Arts & Crafts Globe StandComments (0)
Nothing decks out your library like a proper globe stand.
As was the case with most Americans, my world became a larger place last fall. I began to realize that I had only a vague notion of the location, size and geographical relationship of many of the countries whose names dominated the nightly news. Since I always had a problem with the Mercator projection maps that colored the walls of my high-school classrooms (is Greenland really as large as the United States?) I knew that a globe was the only thing that would give me a clear understanding of what’s what and where.
When I visited my local map store, the globe-stand selection ran the gamut from traditional nautical themes to modern metal sculpture. What I was really looking for, a simple Arts & Crafts-inspired piece, was lacking from the lineup. I decided that the only way that I would be happy with the new addition to my living room was to buy a globe separately and come up with my own base.
Paging through a few of my Arts & Crafts books, the taboret (essentially a small table) appeared to be a staple of the founding fathers of the movement. From Limbert to Mackintosh, Stickley to Wright, there always seemed to be room for yet another small table. With all its variations, it was the perfect starting point for a globe stand. With a little stretching here and a little cutting there, I soon had enough designs to house a galaxy, or at least a small solar system, of globes.
The Stickley variation that I finally built incorporates a lot of the “tricks” – through-mortises, half laps, chamfered and pegged through-tenons, pyramids, and corbels. As it turned out, it was a great project for developing my Arts & Crafts joinery skills. Because all the parts are small, and a limited amount of material is involved, I didn’t become suicidal when a mistake condemned a piece to the kindling bin.
I strayed from the quarter-sawn white-oak norm and chose to use cherry to build the stand. Aside from cherry’s tendency to scorch when being cut, it’s a pleasure to work, easy to finish and, in central Ohio, the price is right.
Around the World in Four Easy Pieces
Start by laying out the four top quadrants. With the exception of the legs, all the parts for this project are sized to be cut from 1 x 6 stock. Before turning to your band saw to test your eye/hand coordination on the outside curves, cut the 1" x 1" mortises. They’re easier to form when there are still flat sides to press against a fence.
While splined joints might have been another “trick” that I could have thrown into the mix, I opted for the ease and familiarity of biscuits when assembling the ring. After gluing up the ring, cut the arcs slightly wide of the line on the band saw. I used a shop-made circle-cutting jig on my router table to refine the outside edge. Then I used a router edge guide to trim the inside edge to a perfect circle.
I also used biscuits to join the two halves of the lower table. I added another level of detail with a ¼" x ¼" chamfer on the top edge of both the ring and table. Finally, I plowed two ¼"-deep x ¾"-wide grooves that crossed in the middle of the bottom of the table to position it squarely on the stretchers.
The legs are formed from 2 x 2 stock. Although the ½" x 2" through-mortises were made on the legs with a straightforward series of cuts with a ½" mortising chisel, the through-tenons required some attention to detail. After cutting the tenons on the ends of the legs to fit the mortises, I determined that a 14° bevel would give me an 1/8"-high pyramidal top. The tenon is sized to allow for an 1/8" vertical rise above the top before transitioning into the slopes. I like the look, and it’s more forgiving than trying to align four pyramid bases exactly with the tabletop.
stretchers are joined with a simple half lap. The ends of the through-tenons
are chamfered at a 45° angle. I then pegged each tenon using 3/8" cherry
dowels through 23/64" holes after slightly tapering the ends of the dowels.
With the holding power of contemporary glues, they’re only for show anyway.
Speaking of show, the corbels that “support” the top are structurally unnecessary to this project. Visually, however, they’re the icing on the cake. Glue them in place and clamp them up.
To mount the globe on the stand, you need to cut two ¼"-long x ¼"-deep notches in the inner edge of the ring. Rather than setting up my router and a jig for the operation, I chucked a ¼" Forstner bit into my drill press, made a ¼"-deep hole that was tangent to the inner edge, and squared up the bore with a sharp utility knife. See the photo at left for details.
Because cherry darkens quickly enough through oxidation and exposure to ultraviolet rays, I used a clear wipe-on oil finish to emphasize the contrast between the end grain of the through-tenons and pegs and the face grain of the legs and top. If you’ve got ’em, you might as well flaunt ’em.
Dan Brody is a home improvement contractor in Columbus, Ohio.
You must be logged in to write a comment. Log In