Close
Sign Up Today and Get a Special 10% Off Coupon

Nova 5/8" Plain Insert

Item #15M80
$24.99
Qty.   or Add to Wish List

 
5.0

(4 reviews)

Read Reviews | Write a Review


Product Information:

Teknatool uses an easy and inexpensive insert/adaptor system on all its NOVA chucks (apart from the Compac). The insert has different lathe spindle thread sizes internally, and simply screws into the back of your Nova chucks. Once the insert is in place, you can then put your chuck onto your lathe.

  • Adapts any NOVA chuck to almost any lathe spindle at low cost.
  • The insert/adaptor versions of NOVA chucks all use the same insert/adaptor system
  • California Residents: Click here for Proposition 65 information.

    Articles:

  • NOVA DVR XP WOODLATHE - This informative article, complete with several videos by Ernie Conover demonstrates the many features of the Nova DVR XP Lathe.
     
     
     

    REVIEW SNAPSHOT®

    by PowerReviews
     
    5.0

    (based on 4 reviews)

    100%

    of respondents would recommend this to a friend.

    Pros

    • Durable (2)

    Cons

    Best Uses

    • At home (2)
    • Reviewer Profile:
    • Avid do-it-yourselfer (3)
    • Primary Use:
    • Personal (4)

    Displaying reviews 1 - 4

    Back to top

    |

     
    5.0

    Special note for Shopsmith Users

    By  Bob

    from Kansas City, Missouri

    About Me Casual Do-It-Yourselfer

    Pros

    • Accurate
    • Durable

    Cons

    Best Uses

    Comments about Nova 5/8" Plain Insert :

    Whereas this adapter (Teknatool PN 'IFNS') works ok with the Shopsmith Mark V, any potential buyer with a Shopsmith should be aware that there is a newer and better adapter from Teknatool with Teknatool PN 'ISNS'. The 'ISNS' adapter has a deeper shoulder and uses a bigger set screw which is angled to match the taper on the Shopsmith output shaft. These features are particularily important with the PowerPro equipped Mark Vs and Mark VII. To repeat, the 'IFNS' adapter works fine with the Shopsmith (I had one for several years with my G3 chuck). But the 'ISNS' adapter is just a bit better.

    • Primary Use:
    • Personal
     
    5.0

    Always Great Products

    By  Slewfoot

    from Sioux Falls, SD

    About Me Avid Do-It-Yourselfer

    Pros

    • Always GREAT products
    • Durable

    Cons

    • none

    Best Uses

    • At Home

    Comments about Nova 5/8" Plain Insert :

    All products that I have purchased from Woodcraft over the Internet and at the Minneapolis store were TOP quality products. All of my transactions with Woodcraft have been good transactions. I have no complaints, only strong recommendations.

    • Primary Use:
    • Personal
     
    5.0

    Exactly what I needed

    By  -

    from Milton, MA

    About Me Avid Do-It-Yourselfer

    Pros

    • Perfect Adaptor Fit

    Cons

    Best Uses

    • At Home

    Comments about Nova 5/8" Plain Insert :

    The adapter was required to mount my new chuck on my Total Shop. It was backordered but arrived when estimated. It is exactly what is needed.

    • Primary Use:
    • Personal
     
    5.0

    Just what I needed to mount the chuck

    By  edspec

    from nc

    About Me Avid Do-It-Yourselfer

    Pros

    • Strong
    • Works Effectively

    Cons

    Best Uses

    • Home Repair
    • Large Projects
    • Small Projects

    Comments about Nova 5/8" Plain Insert :

    Perfectly adapted my nova chuck to the Legacy REVO ornamental mill.

    • Primary Use:
    • Personal

    Displaying reviews 1 - 4

    Back to top

    |