Close
Sign Up Today and Get a Special 10% Off Coupon

Ultimate Plywood Rip & Rout Guide Kit

Item #153650
$99.99
Qty.   or Add to Wish List

 
5.0

(1 reviews)

Read Reviews | Write a Review


Product Information:

The kit includes:

#149196 WoodRiver Clamp Guide Universal Base: This WoodRiver Clamp Guide Universal Base slides accurately in the T-slot found on all WoodRiver Clamp Guides and WoodRiver Guide Rail. Perfect for mounting your circular saw or router to create a precision power tool accessory. 11-1/2" x 6- 3/4" plate with attached guide block for mounting your circular saw or router.

#150002 56" WoodRiver Guide Rail: The base component 56? Guide Rail features the same heavy-duty aluminum extrusion used in the WoodRiver Clamp Guides with integral 1/4? T-tracks and 21/8? x 1/2? profile.

#150003 WoodRiver Guide Rail Connector: The Guide Rail Connector locks together multiple guide rails to form a continuous guide for your circular saw or router across any length material.

#150004 WoodRiver Guide Rail Clamp Pair: These clamps swivel about the “T” shaped anchor and can be placed at any position along the underside of the guide rail extrusion.

#150005 Unique Angle Jig acts as a miter gauge for the Guide Rail System to references any angle from the edge between ±60°.


This system will allow you to place a tool guide for ripping, crosscutting or routing at an acute angle on any size panel. 56" guide rail component features the same heavy-duty aluminum extrusion used in the WoodRiver clamp guides. Guide rail component has 2-1/8" x 1/2" profile with integral 1/4" T-tracks. Guide rail connector locks together multiple guide rails to form a continuous guide for your circular saw or router across any length material. Guide rail clamps secure the guide rail at each end. Clamps swivel about the “T” shaped anchor at any angle. Clamps can be placed at any position along the underside of the guide rail extrusion.

  • Angle jig references any angle from the edge between +/-60 degrees
  • Angle jig has positive stops at 90 degrees, +/-30 degrees, +/-45degrees and +/-60 degrees
  • Guide rail component has 2-1/8" x 1/2" profile with integral 1/4" T-tracks
  • Heavy-duty aluminum extrusion
  • California Residents: Click here for Proposition 65 information.

     
     

    REVIEW SNAPSHOT®

    by PowerReviews
     
    5.0

    (based on 1 reviews)

    100%

    of respondents would recommend this to a friend.

    Displaying reviews 1 - 1

    Back to top

    |

     
    5.0

    Complete package

    By  TheCheezWhiz

    from Indianapolis, Indiana

    About Me Casual Do-It-Yourselfer

    Pros

    • Durable

    Cons

    • No instructions

    Best Uses

    Comments about Ultimate Plywood Rip & Rout Guide Kit :

    The kit provides everything needed to cut sheet goods up to 4' x 8' at any angle. The tool base plate slides easily in the guide with minimal play. It's so nice to not have to worry about the tool wandering away like when using a simple board as a guide. Don't expect the angle jig to assure the cut is exactly 90° from 8' away. It works fine but one really should use layout lines or even another square at the far end for accuracy. Virtually no instructions are provided with any of the items. Granted, not much is needed but a couple things still puzzle me. Why does the connector plate have two extra set screws that bottom out in slots? It appears that perhaps they might force the connector to widen thereby locking it into place from side to side but why? It has 4 set screws that lock it to the guide sections. The clamp posts are able to swivel but that swings the clamp off center from clamping tightly. There must be some purpose to the design. A sentence or two of instructions on both would remove the mystery and probably teach me something. It's not enough to deduct a star rating but something for the manufacturer to consider. Something I wish they'd invent (and include) would be additional slide on quick clamps similar to what typical 90° guides use. They wouldn't extend below the sheet and would make it a snap to make 90° cuts without the under clearance required for the regular clamps.

    Displaying reviews 1 - 1

    Back to top

    |