Save $400 on NOVA 1624-44 Lathe
This may be the only lathe you'll ever need. $999.99 Right Now!
It's a GRR-Ripper Double Pack!
Work safer and more accurately with GRR-Ripper.
Sand & Save $40
You won't find a better sander for less!
While Supplies Last!
Look up product instructions, videos and articles about your favorite tools using our Learning Center.
Join us on your favorite social network! Share your projects and learn from other woodworkers.
Please Note: This item can only be shipped ground to the 48 contiguous states. Some
items cannot be shipped via air due to being flammable, magnetic, contains batteries,
hazardous fumes or where contents are under pressure. Please use a physical address
not a PO Box during checkout.
of respondents would recommend this to a friend.
1 - 6
Back to top
Length too short
WoodRiver Tenoning Jig
It would not reach from my miter slot to the saw blade. I had to install an additional wooden face to the metal face in order to use the tool.
Yes, I would recommend this to a friend
Excellent accessory for joinery
I use this tool for its intended use, very safe to use, it's cuts set- up and cut time by 75% highly recommend tool
Lacking quality control
Mike the Termite
Paso Robles CA
Had to get two of these: After waiting through six-week back order, the first one received had a cracked casting. It was replaced immediately by great customer service, second one had a badly threaded clamp that wouldn't operate. Combined parts from both to get one working unit, and it does work well now. Needed a half-inch board as a spacer on the working face to get the 3/8" tenon I needed, and with that spacer the calibration is fairly accurate on my Craftsman saw. However, now the "front-back" angle brace becomes less usable. Fit and finish are disappointing. Needs careful alignment. If you have the patience to slog through the issues, the tool appears to do what it is designed to do pretty well.
Knurled knob broke on my third cut using the jig. Customer service quickly sent a replacement knob which has held up well. Adjustments could be slightly more precise, but are adequate for my use. I now get good performance from this jig.
IMPOSSIBLE TO SWITCH TO L tilt
As previously noted on another review, the button head screws that must be repositioned for L tilt saws are so tightly inserted I could not remove them..took back to exchange but the second unit had same problem. Store service tried both and couldn't remove even one screw. Got my money back. Either make a Left Tilt option or make it possible to get the screws out.
No, I would not recommend this to a friend
[...]1. Following the instructions to reposition the miter guide bar for a left-tilt saw, one of the button-head screws to be removed was so tight that I almost stripped the hex socket hole.2. The two adjusting screws in the miter guide bar to remove play are loose, and don't hold their position after sliding the jig across the saw table once or twice. Time for some LokTite.3. The "positive stop 2.5mm setscrew (H)" does not provide a positive stop for the vertical work support plate. Instead, it burrows into the metal frame and prevents changing the angle of the vertical work support plate at all. It looks like the screw is oriented 90 degrees away from where it should be. Thus, there is NO positive stop at 90 degrees. >:-(4. The work support clamp screw goes through a slotted piece that is secured with a bolt having a large knob on one end. This knob came loose from the bolt when I tried to tighten it, and clamping the work piece pulled the slotted piece away from the frame! The knob just popped off! Woodcraft is sending a replacement, but the knob should have been pinned to the bolt, not pressed on. >:-(It looks like this tenoning jig will perform well once I get the replacement knob, and if I'm willing to measure for 90 degrees each time I come back from a different angle.
1 - 6
Back to top
©2014 by Woodcraft Supply LLC