$500 Off NOVA 1624-44 Lathe
Whatever projects you turn, the Nova 1624-44 wood lathe will meet your needs for a lifetime.
Buy Now $899.99
Go Mobile w/Heavy-Duty Casters
Save 30% on Heavy-Duty Casters through April 25.
Shop Sizes & Styles
Buy Laguna 14-12 Bandsaw & Get a Free Industrial Flood Light
Perfect for serious woodworkers and hobbyists.
Look up product instructions, videos and articles about your favorite tools using our Learning Center.
Join us on your favorite social network! Share your projects and learn from other woodworkers.
Please Note: This item can only be shipped ground to the 48 contiguous states. Some
items cannot be shipped via air due to being flammable, magnetic, contains batteries,
hazardous fumes or where contents are under pressure. Please use a physical address
not a PO Box during checkout.
of respondents would recommend this to a friend.
1 - 10
Back to top
Not so accurate circle cutter
I live for pain.
AccuRight Band Saw Circle Cutting Jig
Wood kept moving off circle cutter pin. I returned it to the store.
No, I would not recommend this to a friend
It Works well
It works well and cuts a nice circle. You have to be careful to keep the work piece properly vertical, though. Allowing the piece to tilt from one side to another will push the blade to the side. Also, standing the side of the blade/saw seems to be a safer and more controlled position for cutting the circle.
I'm an engineer and expect a bit better design. So maybe this next part is over critical. The clamping system is a poor and flimsy design and should be improved. They got cheap out on that part. I will improve upon that very soon. Likewise, the instructions are poor. I mean they should be embarrassed to even include them. The system is not hard to figure out if you have any mechanical inclination. But how much effort does it take to write a decent set of step by step instructions?!?!?! Or even include some advice on aligning the tool and securing it properly?
Between the clamping and lack of proper instructions, this device could pose some safety risks. Ensure the device is firmly clamped in place before attempting use it. Make sure the centering pin aligns properly with the blade and that there is room between the saw blade and the supporting aluminum channels. Calibrate the scale by aligning the zero with the blade.
I gave it only 3 stars because of the sub standard instructions and the poor clamping design.
Yes, I would recommend this to a friend
opened the box and one hole clamp assembly and one stabilizer was missing so I had to make my own clamps just so I could use it. we will see how long it takes costimer service to get me a clamp. so far i'm not impressed.
Carter circle cutting jig
Instructions could use improvement in my opinion.
The jig is much easier to set up when not using the Carter mag fence as a table extension.
Also I did find the wood blank to be a bit wobblier then I would have liked.
All in all the jig does cut circles, but assembly, instructions and operation are not top notch.
Easy Set Up
The set up is quick and easy. Accurate cuts. It would be nice if you could slide the cut to the stop thus making cutting a bigger than final size board a quicker cut.
works very well
Works well once you get it set up
Relatively easy to set up, works as advertised. NIce rig, not too expensive.
Circles made easy!
I use this tool for all my circle cuts and the setup to the bandsaw is quick and easy even without the recommended magfence attachment. The assembly plans could use alot more work, however it isn't hard to figure out on your own.
Good Jig but a couple of tricks u need
rob in pa
Bought this for a project I was doing using Bubinga. Wood is beautiful, expensive and hard! Fixture works well except there are 2 tricky things. First to get the center punch on the pivot post you need to get down low with a flashlight to make sure you are in the punched spot. If you do not get in the punch it will walk. Second you need a starting edge at exactly your diameter because there is no way to lead the band saw in when you are on the pivot. If the saw blade is pushed on too much when the piece is on the punch you can use a belt sander to make a slight divot in the edge to start the saw. Finally circles I cut were not perfect but pretty close. I believe the variance was due to the blade bending slightly in very hard wood.
Fit my Jet 14
Maybe the instructions have changed since the last person reviewed it, but I had no problem following the instructions and installing the jig. I watched the videos on the Carter site first, which helped, but install was still a snap on my 14" Jet saw with riser block.
Cutting circles could not be easier, just make a center punch, mount your wood, slide forward until it hits the stop and rotate. I agree with the last review it can be a little tippy, but I realized I was doing it slightly wrong at first. If you follow the directions and place downward pressure on the center and hold it there then everything stabilizes. It takes a little getting use to, but after that I've made countless perfect circles with total stability. I've even used it to cut some larger 4 foot 1" oak ply to make a card table. I LOVE THIS THING. My main reason to buy it was to salvage scraps of high dollar wood that I turn bowls with. It allows me to keep what otherwise would end up as chips and dust on the floor. It also allows me to get closer to the final diameter in the rough cut then I ever did before. I then can use more of the scrap wood to make pens and smaller turning projects. I also have had the Carter guides on my saw for many years and love them. Another fine product from Carter, thanks.
1 - 10
Back to top
©2014 by Woodcraft Supply LLC